How to Use a Bullet Puller The Right Way?If you are a person who enjoys reloading your own ammunition, that having the proper tools is extremely important to your craft. Like any other kind of endeavor like this, you want to make sure you have the absolute best equipment so that you can perform any task if you know how to use a bullet puller.

The truth is that there are going to be times when you are going to make mistakes in creating the ammunition. Either you have ceded the bullet to deep, or maybe you realize that you did not have the proper amount of powder inside the cartridge. Whatever the situation, you need to buy a bullet Puller to be able to take that round apart, or all of your rounds apart so that you can reuse the brass and powder. This is a way to ensure that you don’t waste your money.

A Safe Tool to Use

The essential part of using a bullet puller is that this will safely remove the ammo and powder from the cartridge without damaging that cartridge. This allows you to keep it in good condition so that it can be used over and over again.

There are two different types of bullet pullers – the kinetic and the cam-lock. While both work extremely well at their task, the way you use each one of these devices is different than the other. This is something that is important for you to know.

Is This Safe?

Before going over the instructions on how you would take ammunition apart, it is important to discuss one of the most commonly asked question related to the bullet puller. You were dealing with ammunition, which makes many understandably squeamish. They want to know if it is safe to actually use either types of this device.

The truth is that they absolutely are. Literally millions of people use these products each and every year without incident. They are designed to provide a safe means to be able to take apart a cartridge without causing injury, so you can have confidence in deciding to buy one of these devices.

How to Use the Kinetic Puller?

The kinetic puller, also referred to as the inertia puller, looks very much like a hammer. Included within the kit that you purchase there will be several different pieces, including o-ring bands. These help you to hold the cartridge in place while you are dislodging the ammunition. Here are the steps on how you would use this.

  • You first want to assemble the collet. This is used to actually hold the shell casing in place to help dislodge the bullet. Depending upon the kind of puller that you buy, you may come with several different sizes for the collet, so you will want to get one that fits the specific cartridge you are using. If this is not included in the kit you will need to purchase it.
  • Once the collet is assembled, you will insert the cartridge into the cap of the puller. The collet captures the cartridge in place, to ensure that it does not become loose during the striking process.
  • Next, you will want to strike the puller against a hard surface. Depending upon the kind of product you are choosing, you may have success using nothing more than a hard piece of wood. However, many options will tell you that you need a stronger surface, such as concrete or steel. With each strike, stop and make sure that the cap remains tight. It should take you no more than three or four strikes at most two break apart the cartridge. If you are finding it is taking more than that you are likely doing something wrong.
  • Once you have successfully dislodged the cartridge, separate the different components that you have inside your cartridge. This includes getting all the gunpowder out, as well as the ammunition.

Tips for Using the Kinetic Puller

One of the challenges that people have in using this kind of puller is that they become genuinely concerned about the fact that they are striking ammunition against a hard surface. This creates a lot of animosity, but you should be well aware that this is a process is that works successfully and poses no danger to you as long as you are following the instructions.

You should also be aware that you don’t need to take it easy on the device. You should strike it hard, with a great deal of momentum to dislodge the cartridge. Understand that what you could accomplish with one or two strikes will take eight or more if you are not giving enough force. This takes some practice, but over time you will understand how to use the device fully.

Included inside the puller will be a piece of foam or rubber that helps to prevent the bullet from becoming dented during the striking process. This absorbs the impact, protecting your cartridge.

Levis has been a blogger for many years, and has a considerable amount of experience as an internet marketing executive. The idea behind the site was actually his brainchild. He had spent years using his skills as a marketing executive to help market and promote products and services and wanted to do something that really had an impact on consumers. He built a small team to help him get the site off the ground and to help develop the strategy behind what Safety Winner is all about.

LEAVE A REPLY

Please enter your comment!
Please enter your name here